What is component preparation and when is it needed before assembly? - Eurocircuits

EUROCIRCUITS / KNOWLEDGE CENTRE

What is component preparation and when is it needed before assembly?

Component preparation is the work done on components before they are placed and soldered on a PCB: forming or trimming leads, tinning terminations, baking moisture-sensitive devices, programming parts, and repackaging components so they run on an SMT line. It is needed when parts arrive in a form, condition or state that the assembly process cannot use directly. This article answers the practical questions engineers ask about it, from which parts need it to how design choices can reduce it.

Which components need preparation before PCB assembly?

Components that need preparation are those that do not arrive ready for automated placement and soldering. Typical examples are through-hole parts with long or misshapen leads, moisture-sensitive devices, programmable ICs and memories, parts with oxidised or unsuitable terminations, and components supplied in loose or non-standard packaging.
In more detail, the most common categories are:

  • Through-hole components: axial and radial parts often need their leads formed or cut to match the hole pitch and board thickness.
  • Moisture-sensitive devices (MSDs): plastic packages such as BGAs, QFNs and some QFPs absorb moisture and may need baking before reflow if their exposure limit has been exceeded.
  • Programmable devices: microcontrollers, flash memories and similar parts may need firmware loaded before placement.
  • Parts in loose or unsuitable packaging: cut tape, bulk bags or tubes that do not suit the feeder or placement machine need repackaging.
  • Components with poor solderability: terminations that are oxidised or finished in a way that does not suit the process may need tinning.

Which parts fall into these categories depends on the design, the components chosen and how they were stored and supplied, so each BOM needs to be checked individually.

What does component preparation involve in practice?

Component preparation involves a set of hands-on and machine-assisted steps that bring a part into a condition suitable for assembly. The main activities are lead forming, tinning, baking, programming and repackaging, each addressing a specific mismatch between how a component is supplied and how the assembly process needs it.

Lead forming and cutting

Through-hole components must fit the board’s hole spacing and seat correctly. Lead forming bends leads to the right pitch, while cutting sets the lead length so that it protrudes correctly through the board for soldering. Consistent forming also reduces mechanical stress on the component body.

Tinning and solderability preparation

Tinning coats component terminations with solder to improve wetting. It may be considered when terminations are oxidised or when a finish is not compatible with the soldering process. The exact approach depends on the component and the process, so it should be agreed with the assembler rather than assumed.

Baking moisture-sensitive devices

Moisture-sensitive devices are classified by moisture sensitivity level, which sets how long they can be exposed to ambient air before reflow. If that floor life is exceeded, or the humidity indicator shows exposure, the parts are baked to drive out absorbed moisture. This reduces the risk of package damage such as cracking or delamination during reflow.

Programming and repackaging

Programming loads firmware or configuration data into devices before they are placed. Repackaging transfers components from loose bags or short cut tape into formats that suit feeders and pick-and-place machines, such as reels, trays or tubes. Both steps happen before the parts reach the line.

When is component preparation needed before assembly?

Component preparation is needed whenever the supplied state of a component does not match what the assembly process requires. The usual triggers are through-hole leads that do not fit the board, an expired moisture exposure limit, devices that must carry firmware, and packaging that cannot be fed to a placement machine.
Common situations include:

  1. Prototype builds with mixed sourcing: parts arrive from several distributors, often as cut tape or loose bags rather than full reels.
  2. Customer-supplied (consigned) components: storage history and packaging are unknown, so moisture exposure and solderability need checking.
  3. Designs using MSDs: any time the floor life has been exceeded or the package integrity is in doubt.
  4. Designs with programmable parts: where firmware must be present before the board is tested or used.
  5. Mixed-technology boards: SMT and through-hole parts together, where through-hole leads need forming before insertion.

Because prototypes and low-volume builds are small and varied, preparation tends to be more frequent than in stable, high-volume production where components are supplied in standard formats.

How does component preparation affect assembly quality and lead time?

Component preparation protects assembly quality by removing avoidable causes of defects such as poor wetting, misaligned through-hole parts or moisture-related package damage. It also adds process steps, so it affects lead time. Preparation done early and planned into the schedule usually costs less time than problems discovered during assembly.
On the quality side, correctly formed leads seat properly, tinned or clean terminations wet more reliably, and baked moisture-sensitive devices are less likely to be damaged during reflow. Programmed parts avoid a separate handling step after assembly.
On the lead time side, every preparation step takes time, and it can only start once the right components are physically available. Incomplete or inconsistent BOM information is a frequent cause of delay, because it forces clarification before preparation can even begin. Verifying component identities, manufacturer part numbers and packages against the BOM and placement data before assembly helps identify these problems early. A short quoted assembly time does not guarantee a short overall cycle if components arrive in the wrong form or with unclear data.

How can engineers reduce the need for component preparation?

Engineers can reduce the need for component preparation by choosing components that suit automated assembly, specifying them unambiguously in the BOM, and ordering them in suitable packaging. Fewer special cases mean fewer manual steps, fewer clarifications and a lower risk of avoidable iterations.
A practical checklist:

  • Prefer SMT parts where the design allows: they are generally easier to place automatically than through-hole parts that need lead forming.
  • Complete the BOM: include manufacturer part numbers, packages and polarity information, and keep the BOM consistent with placement data.
  • Order in assembly-friendly packaging: reels, trays or tubes rather than loose bags, and avoid very short cut tape where possible.
  • Check moisture sensitivity early: note which parts are MSDs and keep their original sealed packaging and handling information.
  • Flag programmable parts: state clearly which devices need firmware and provide the programming files and requirements.
  • Store components properly: good storage limits oxidation and moisture exposure before the parts reach assembly.
  • Verify before you order: confirm component identities and packages against the design so data problems are found before physical parts are committed.

These steps do not remove the need for engineering iterations that test and improve a design. They reduce the unnecessary ones caused by avoidable preparation and data problems.

How Eurocircuits helps with component preparation

Eurocircuits manufactures and assembles PCB prototypes and low-volume builds in-house, so component preparation sits within the same organisation as PCB fabrication and assembly. Its Right First Time approach focuses on identifying avoidable preparation and data problems before physical production begins, which keeps unnecessary iterations to a minimum.
Where this is relevant to your project, Eurocircuits can support you with:

  • Component verification: checking component identities, manufacturer part numbers and packages against your BOM and placement data, supported by a Verified Component Database.
  • Pre-production verification: analysing PCB and assembly data before production, so inconsistencies are found while changes can still be made digitally.
  • Integrated PCB and assembly: one manufacturing partner for fabrication and assembly, which reduces interfaces between suppliers and simplifies engineering communication.
  • Prototype and low-volume focus: experience with the small, varied component sets typical of PCBA prototypes and NPI builds.

Explore the Eurocircuits services to see how PCB and assembly support fits your build, or contact the Eurocircuits team to discuss the component preparation needs of your next project.

Related Articles